What is a Good Cold Air Intake
Login  | |
|
What is a Good Cold Air Intake - 1/30/2004 3:26:04 AM
|
|
|
NeoTokyo
Posts: 2517
Joined: 12/2/2003
From: Sacramento, CA
Status: offline
|
I have been looking around for a better Cold Air intake setup for my 1995 Mustang V6. Right now its stock, and we all know that only flows 550cfm. Im looking for something that flows closer to 800cfm.
Im also looking for a very large Throttle Body, but the largest I can find is only about 64mm I think. What is the largest I can get without modding my intake manifold? And who can I get it from? Also is there a kit out there with a custom intake manifold and TB on it? Or can i buy them separatly? All links would be much appriciated :)
Thanks everyone.
|
|
|
|
|
|
|
What is a Good Cold Air Intake - 2/1/2004 7:30:21 PM
|
|
|
N2OJunkie
Posts: 1592
Joined: 1/3/2004
From: United States
Status: offline
|
![]("http://images.cardomain.com/member_images/2/web/506000-506999/506450_9.JPG) BBK 70mm TB and CAI![]("http://images.cardomain.com/member_images/2/web/506000-506999/506450_40.JPG) ![]("http://images.cardomain.com/member_images/2/web/506000-506999/506450_10.JPG)
|
|
|
|
|
What is a Good Cold Air Intake - 2/8/2004 9:06:39 PM
|
|
|
NeoTokyo
Posts: 2517
Joined: 12/2/2003
From: Sacramento, CA
Status: offline
|
I like that, thats a good looking CAI, like your Pony plate on your intake manifold too. I know just where to buy that. Thanks NO2
|
|
|
|
|
What is a Good Cold Air Intake - 2/9/2004 7:19:43 PM
|
|
|
N2OJunkie
Posts: 1592
Joined: 1/3/2004
From: United States
Status: offline
|
The pony plate is on the stock plenum (not intake manifold)and is standard on all Stangs 99 and up, thanks though.
|
|
|
|
|
What is a Good Cold Air Intake - 2/9/2004 11:00:18 PM
|
|
|
NeoTokyo
Posts: 2517
Joined: 12/2/2003
From: Sacramento, CA
Status: offline
|
Hmmm, looks good 
Your intake is alot different then mine, but that is to be expected cause mines a V6. That pony plate would be on my runners it i tried compaired them. A manifold that we were going to use on our 70' vette 350 Z block was the Performer RPM because of the large plenum it had. Thanks for plenum space it helps to force a denser charger of air and fuel into the engine, since the space in a plenum has a higher pressure then outside of it.
|
|
|
|
|
What is a Good Cold Air Intake - 2/10/2004 2:26:39 AM
|
|
|
hotrodman
Posts: 2045
Joined: 12/18/2003
From: United States
Status: offline
|
BBK
|
|
|
|
|
What is a Good Cold Air Intake - 2/10/2004 4:35:46 AM
|
|
|
2000GT4.6
Team MF Member #2046
Posts: 12443
Joined: 1/22/2004
From: United States
Status: offline
|
Why are you looking for such a large MAF and T/B ?
|
|
|
|
|
What is a Good Cold Air Intake - 2/11/2004 1:24:51 AM
|
|
|
NeoTokyo
Posts: 2517
Joined: 12/2/2003
From: Sacramento, CA
Status: offline
|
Forced induction and highly modified bottom end, heads and intake manifold. Nothing is going to be left alone on this block.
|
|
|
|
|
What is a Good Cold Air Intake - 2/11/2004 1:05:37 PM
|
|
|
Hotrods_n_Booze
Posts: 13193
Joined: 12/29/2003
From: Southern California
Status: offline
|
Like HotRodMan said. BBK is the only one I could find for the V6, but there my be more now. I last looked a few months ago when I bought my 72mm. But BBK is a good company. Mac listed one but it was never available.
I wouldn't get the big T/B untill you do a power adder or it will run bad,(bottom end loss) Bigger MAF will help on your year, but nothing great untill you get a bigger T/B, so do them both at the same time you add your forced air.
Super Six recomends 60mm with thier stage 3 power pack (which is N/A), so that must mean that as long as your N/A 60mm is ok.
|
|
|
|
|
Printable Version
