wildstang 384
04-06-2008, 06:16 PM
I need to remove my drivers side door panel. Has anyone done this before. HELP!!
|
View Full Version : Door Panel wildstang 384 04-06-2008, 06:16 PM I need to remove my drivers side door panel. Has anyone done this before. HELP!! bronxbomba63 04-06-2008, 06:25 PM I believe there are about 6 screws around the door panels that you would have to unscrew to take the panels off. there are an additional 2 (one behind the door handle, one somewhere around the handle around the window controls). these are found after you remove the panels. OIIIIO 04-06-2008, 06:27 PM http://www.allfordmustangs.com/forums/attachments/2005-mustang-v6-tech/30471d1184795420-2005-mustang-door-panel-removal-door-panel-removal.pdf bronxbomba63 04-06-2008, 06:37 PM there you go.....nice link wildstang 384 04-07-2008, 06:06 AM Thank you for the info. I am getting a new Left side mirror. I just want to make sure I do it right. 157db 04-07-2008, 04:56 PM Straight from Ford: http://iihs.net/fsm/?dir=441&viewfile=Door%20Trim%20Panel.pdf Exterior Mirror http://iihs.net/fsm/?dir=448&viewfile=Exterior%20Mirror.pdf Exploded View http://iihs.net/fsm/?dir=448&viewfile=Exterior%20Mirrors%20Exploded%20 View.pdf wildstang 384 04-07-2008, 07:17 PM The window rattles when I hit a bump in the road or close the door. I think the car was wrecked before I bought it. I didn't notice these things until about 6 months after I bought it. Does anyone know how to tigten the brackets so it doesn't rattle as much? 07lane40 04-07-2008, 07:21 PM i'd say just open 'er up and tighten those bolts... 157db 04-12-2008, 10:35 AM DynaMat DynaMat after tightening the bolts ;) wildstang 384 04-12-2008, 03:16 PM Dyanmat? Devil Wolf 04-12-2008, 08:21 PM its sound dampening material. NocturnalV6 04-12-2008, 08:44 PM aye dynamat is being used big time wildstang 384 04-25-2008, 08:27 PM I finally got to get into changing the mirror and checked on all the bolts. They are all tight. The darn window still rattles. I didn't put the Dyanamat. That will soften the sound but it's still going to rattle. 157db 04-26-2008, 10:50 AM ORIGINAL: wildstang 384 I finally got to get into changing the mirror and checked on all the bolts. They are all tight. The darn window still rattles. I didn't put the Dyanamat. That will soften the sound but it's still going to rattle. Check the nut on the bottom of the door and the nut under the red reflector on the door panel for tightness. ;) Next its time to check the door handle. Sure the noise is window related or in the door somewhere? local://upfiles/69445/31963B3EAB7A4BC49B21A3134EB6C363.jpg my06shaker 04-26-2008, 11:17 AM While you're in there swap out those lame factory speakers for some quality ones and those door handles for the good lookin' Silverhorse handles. local://upfiles/86175/DF59EFFFA080407992C3FC0761F96461.jpg local://upfiles/86175/FAA8EA52DAF7400AA42BF8F6972F2F99.jpg |