Patriot Alum Heads 185cc $$SALE$$ Pics...>
Login  | |
|
Patriot Alum Heads 185cc $$SALE$$ Pics...> - 10/26/2007 9:50:03 PM
|
|
|
Texas_Hot_Rods
Posts: 194
Joined: 12/26/2006
Status: offline
|
Well,
we received the first batch of heads and they look pretty nice compared to the stock E7's. For the money, these will be a solid choice for those searching for some serious power gains on the cheap. Here's some pics as we tore down one of our mechanics 84 GT for the swap. We'll have them installed and running late tonight so dyno results will be tomorrow if we're lucky.
Anyway, for now you can see the dramatic difference in the chambers, bowls, valve sizes, and port comparisons. Sorry for the rough pics, but we didn't want to wait to get these tested and let you know what to expect from them. For the 1st 6 sets we have left we're running an intro deal at $850 shipped. These come assembled complete, ready to bolt on and sprung up to a .550 lift hyd roller cam.
Here's what you'll need for the swap:
Heads $850
Rockers (3/8 stud mount) $229
Head Gaskets (Felpro 1011-2) $70/pr
Intake Gaskets (Felpro 1250) $25/pr
Exhaust Gaskets (Felpro 1415) $20/pr
Hardened Pushrods (may change from stock pending your cam) $86/set
Valve Cover Gaskets (rubber or cork) $15/pr
ARP Head Bolt Kit (ARP-154-3601 ) $40/set
Total: $1335 in parts Labor if you have someone or a shop swap would most likely run between $250-$600. Not bad for a serious bump in HP/TQ as well as an extra 50-75lbs off the nose of your steed.
Here are some other recommended parts to add to the build if you're looking for even more power and performance:
Intake Manifold (EFI) $350-$550
Hyd Roller Cam $150-$190
New Roller Lifters $110/set
New Dbl Roller Timing Set $40-$75
Front Cover Gaskets $25
65mm-75mm TB & EGR $200-$325
Cold Air Kit $140-$190
Rear Gear Upgrade (3.55-4.30) $150-$225
Headers (Long Tube or Short) $125-$300
Mid Pipe to go with Headers $130-$185
That should give you guys a ton of options on getting the most out of a tired fox. If you don't think the engine is up to spec or just has too many miles then we also have shortblocks or longbocks available from $1599 (306 - balanced and blueprinted with Forged Probe Pistons, Prepped Rods, Prepped Crank, New block 0.30 over, including ARP main & rod bolts and performance rings & bearings, assembled and ready to add the above parts to.)
Check out the pics and let us know what you think...results coming soon.
Compare the Stock E7's to the new Patriot Freedom 185 cc Alum Head with 2.02 & 1.6 Valves 60cc chambers:
Here's the little 306 stepping up:
_____________________________
Brian Metzger
Texas Hot Rods
www.texashotrods.com
877-50-STANG
|
|
|
|
|
|
|
RE: Patriot Alum Heads 185cc $$SALE$$ Pics...> - 10/26/2007 10:18:03 PM
|
|
|
86 5.0L
Posts: 4921
Joined: 7/29/2006
Status: offline
|
looks good
_____________________________
|
|
|
|
|
RE: Patriot Alum Heads 185cc $$SALE$$ Pics...> - 10/26/2007 10:25:38 PM
|
|
|
OnyxCobra
Posts: 6956
Joined: 11/27/2005
From: Chicago - in Rochester, NY
Status: offline
|
Nice looking heads.
_____________________________
CarDomain - My Website
|
|
|
|
|
|
|
RE: Patriot Alum Heads 185cc $$SALE$$ Pics...> - 10/26/2007 11:25:02 PM
|
|
|
Stella94GT
Posts: 728
Joined: 12/13/2006
From: chicago
Status: offline
|
850 is a rediculously good deal. i wish i could pick up a set right now
_____________________________
CAI, 75mm MAF, 70mm TB, 3.73''s, Long Tubes, O/R X Pipe, Straight Pipes, B&M Short Throw Shifter, 15* Timing.
Waiting to install: GT40 intake + Cobra 1.7rr.
|
|
|
|
|
RE: Patriot Alum Heads 185cc $$SALE$$ Pics...> - 10/26/2007 11:52:10 PM
|
|
|
TTGreenSN95
Posts: 629
Joined: 3/25/2007
Status: offline
|
Those heads look ported to me are they ported or right out of the box?
Just wanted to know so we dont expect the same dyno numbers from an unported set?
I did not see in your post were you mention that these heads are ported?
see image.........
 Attachment (1)
< Message edited by TTGreenSN95 -- 10/26/2007 11:56:23 PM >
_____________________________
|
|
|
|
|
|
|
RE: Patriot Alum Heads 185cc $$SALE$$ Pics...> - 10/27/2007 7:50:44 AM
|
|
|
bikeboy587
Posts: 1497
Joined: 3/26/2007
Status: offline
|
if i had the money i would be placing an order right now!
_____________________________
306|Ross Forged Flattop pistons|Tubular GT40 u/l(ported)|Edelbrock Performer 5.0|TFS stg 1|Zex 125hp dry
Mustang dyno:
NA 301rwhp/364rwtq
N2O 374rwhp/504rwtq
|
|
|
|
|
|
|
|
|
RE: Patriot Alum Heads 185cc $$SALE$$ Pics...> - 10/27/2007 9:06:37 AM
|
|
|
thesource
Posts: 258
Joined: 1/1/2007
From: Texas of course
Status: offline
|
These heads are the ProComp castings . They are a replica of the Vic Jr head and are from Austrilia but casted in China . I have a set of some of the very first ones done . They are 220 cc CNC'd heads with a 2.05/1.60 valve . The CNC work was done through Avenger Cylinder heads , the same guys that did some of the Canfield stuff . I have them on a 393W and they are pretty decent for the price I paid for them .
_____________________________
http://www.mymustangsite.com/thesource/
I buy T5 & T56 cores
|
|
|
|
|
Printable Version
