DIY: HOW TO Install Hood Pins $13.00... UPDATED!!!
Login  | |
|
DIY: HOW TO Install Hood Pins $13.00... UPDATED!!! - 9/16/2007 2:19:55 AM
|
|
|
Boozshey
Posts: 1838
Joined: 5/19/2005
Status: offline
|
So I stopped by Autozone and found the SPECTRE hood pins were only $7.99 compared to PEP-BOYS at $12.99. My Autozone didn't have the rubber lanyards, so I did have to drive to PEP-BOYS to get them at $4.99.
TOOLS/MATERIAL REQUIRED:
SPECTRE HOOD PINS AUTOZONE PART NUMBER 42563 ($7.99)
SPECTRE LANYARDS PEP-BOYS ($4.99) (Autozone part number 4264 but are $8.99)
TAPE
DRILL
1/2" DRILL BIT
1/4" DRILL BIT
1/8" DRILL BIT
FLAT HEAD SCREW DRIVER
PHILIPS SCREW DRIVER
SMALL ENOUGH SCREW DRIVER TO FIT THROUGH HOLES IN THE HOOD PINS (MORE LATER)
3/4" WRENCH
DREMEL WITH WHEEL
CAR WAX, PEANUT BUTTER, GREASE (1 OF THE 3 IS FINE)
RED LOCTITE
(NOTE: I didn't use a tape measure. I simplied used pre-marked areas that were on both sides. Made all the measuring a sinch.)
STEP 1:
Remove the 6 body pins that hold on the plastic radiator cover.
STEP 2:
There are 2 long seams in the support on the front rail. I used the inside ends on both sides to mark the spot for the hood pins. I started with a 1/4" hole then drilled the half inch hole.
STEP 3:
I placed the hood pins in the location, but don't tighten down yet. You are only using them to make the marks for the holes in the hood.
STEP 4:
Tape the top side of the hood. I didn't know the exact spot so just guessed and covered a bigger area.
STEP 5:
Remove the under hood liner. Due to the shaker hood, to remove mine would be huge task, so I simply taped it back.
STEP 6:
Take some wax, peanut butter, grease, or whatever else you can find and place a small ball on top of the hood pin.
STEP 7:
Close the hood and press on both sides to allow the material from the hood pins to transfere to the underside of the hood.
STEP 8:
Drill from the bottom of the hood up. Start with the 1/4" bit and then the 1/2" bit.
STEP 9:
Sorry no pics of this. Just forgot... But...
Remove all the tape,
Install the under hood liner,
Close the hood and the hood pins will start to press through the liner,
Press harder and they will pop through giving you a nice hole,
Open the hood and just pull the extra material out of the under hood liner.
Step 10:
You will notice the holes might need to be bigger here and there. Just do what you need to do and make the hood pins fit through the holes without rubbing. No art here, just make the hole bigger.
STEP 11:
After makeing the holes bigger and the pins now fitting through the hood, you will have to adjust the height of the pins. THEY DO FIT... The bottom nut will only be holding about 3-4 threads. So get it set at the right height and get an idea of that position. Now take the pins off the car and loctite in the proper order to reassemble. Once you have them reassemble tighten the top bolt with a 3/4" wrench. To keep the pin from moving place a screw driver through the hole in the top of the hood pin.
Step 12:
Locate the spot weld to the left/right of the hood pins. I made a spot next to them since they are the same on boths sides. I drilled an 1/8" hole there and screwed in the lanyard.
STEP 13:
Place the radiator cover back on and mark the spots that need to be cut out. Dremel away...
STEP 14:
I chose to run the lanyard under this part to get rid of a lot of the extra slack. Turned out nice.
STEP 15:
Forgot pics again, but pretty easy...
Close the hood up and place the steal plates over the pins on the hood. TIP: DO ONE HOLE AND SCREW AT A TIME... Hold the plate in place and drill a 1/8" hole in the first spot. Screw it down and then repeat. If you try and drill all 4 holes first it won't align right. TRUST ME!!!
STEP 16:
Some have had problems with there still not being enough of the hood pin showing. To fix the problem, just lower the bump stops evenly to allow for more space. This will take some trial and error but make sure that you do both sides evenly. If you lower them to much though, your hood will not align with the fenders properly, but 1/2-1 full turn shouldn't make it so noticeable.
FINISHED PRODUCT!!!
 Attachment (2)
< Message edited by Boozshey -- 12/14/2007 6:43:34 PM >
_____________________________
http://www.americanmuscle.com/
|
|
|
|
|
|
|
RE: HOW TO Install Hood Pins... With PICS!!! - 9/16/2007 5:25:41 AM
|
|
|
TPony
Posts: 9381
Joined: 7/29/2006
Status: offline
|
Good looking.
_____________________________
06 GT, tint, appearance mods, 18X9 w/NT555 255/45/18, GTA Axlebacks, GT500 spoiler/pedals. Many interior billet upgrades.
|
|
|
|
|
RE: HOW TO Install Hood Pins... With PICS!!! - 9/16/2007 5:56:32 AM
|
|
|
Thurman
Posts: 2267
Joined: 1/5/2007
Status: offline
|
Good job!
_____________________________
07 GT COMP CAMS, ZEX,PROCHARGER,STAGE III CLUTCH BBKTB, 410'S, HURST, DIABLO, DUCT TAIL,CDC CLASSIC,KOOKS,CORSA, UCA & LCA, S/B DELETE,PROTH MTS, LINE LOCKS, D SPECS, DR'S,SPYDER SHAFT, 6 PT ROLLCAGE DD'S,CMDP,552.9 RWHP 486.1 TORQUE
|
|
|
|
|
RE: HOW TO Install Hood Pins... With PICS!!! - 9/16/2007 5:58:52 AM
|
|
|
Rdot9
Posts: 1726
Joined: 6/7/2007
From: Connecticut
Status: offline
|
very nice, good job!
_____________________________
07 V6
4.0 POWER!!!!
SwtPnyChick been learnin me good since 3/31/2008
-Ryan-
|
|
|
|
|
RE: HOW TO Install Hood Pins... With PICS!!! - 9/16/2007 8:05:48 AM
|
|
|
PROMETHEUS PRIME
Team MF Member #510
Posts: 2336
Joined: 11/19/2006
From: Southern Cali
Status: offline
|
Looks good.
_____________________________
Stangpede FTMFW!!!!
|
|
|
|
|
RE: HOW TO Install Hood Pins... With PICS!!! - 9/16/2007 8:37:03 AM
|
|
|
rogan01
Posts: 566
Joined: 5/6/2007
Status: offline
|
What kind are those? Any install tips? Looking to do the same.
Nice job.
|
|
|
|
|
|
|
RE: HOW TO Install Hood Pins... With PICS!!! - 9/16/2007 6:33:43 PM
|
|
|
5SPD07GT
Posts: 823
Joined: 7/12/2007
From: Woodbridge, VA soon
Status: offline
|
looks great, i dont have a pepboys though
_____________________________
|
|
|
|
|
RE: HOW TO Install Hood Pins... With PICS!!! - 9/16/2007 6:55:07 PM
|
|
|
Bluestar
Posts: 2877
Joined: 2/24/2007
Status: offline
|
Very nice.........Great job.....
_____________________________
"A man's gotta know his limitations"...Clint Eastwood
|
|
|
|
|
RE: HOW TO Install Hood Pins... With PICS!!! - 9/16/2007 6:58:01 PM
|
|
|
dbwheelsjd
Posts: 47
Joined: 4/16/2007
Status: offline
|
nice job, good detail. def a mod i plan on doing after i put some $$$ under the hood
|
|
|
|
|
|
|
RE: HOW TO Install Hood Pins... With PICS!!! - 9/16/2007 7:48:14 PM
|
|
|
owero01
Posts: 1341
Joined: 8/27/2006
Status: offline
|
Great job. I'm thinking about doing the same.
_____________________________
Pro 5.0 STS, C&L CAI with D/S 93, Steeda UDPs, Spohn LCAs & UCA, FRPP 4:10, JPC D/S, Eibach springs, D Specs, P/h bar, Chr VCs, FM 40s, BO Strut Brace, Seq. TLs,
|
|
|
|
|
RE: HOW TO Install Hood Pins... With PICS!!! - 9/17/2007 6:35:09 AM
|
|
|
rogan01
Posts: 566
Joined: 5/6/2007
Status: offline
|
Thanks "Taco" Boozshey" - greatly appreciated.
BTW - I didn't get the link on the type of pins you used... Could you please repost?
quote:
ORIGINAL: Boozshey
Here ya go... HAVE AT IT!!!!
|
|
|
|
|
|
|
RE: HOW TO Install Hood Pins... With PICS!!! - 9/17/2007 8:47:53 AM
|
|
|
300GT
Posts: 750
Joined: 8/4/2007
From: Coatesville, PA
Status: offline
|
Looks good. Has to be the first how-to I've read on here that has peanut butter on the list of items needed!
_____________________________
5 speed/3.55's/MAC axle backs/sequential tail lights/Agent 47 mirrors/Silverhorse Racing louvers and grill inserts
|
|
|
|
|
RE: HOW TO Install Hood Pins... With PICS!!! - 9/17/2007 9:34:53 AM
|
|
|
157db
Posts: 4391
Joined: 5/16/2007
From: NW Arkansas
Status: offline
|
I expected to see crackers on the items needed list.
Super job and write-up.
_____________________________
AiRaid CAI
Saleen Short Shifter
F/R GT Sways
GT M/T TakeOff Muffler
Roush Rear Shocks/Springs
Roush Hoodscoop
Roush Window Louvers
SS Eleanor Grill
Pony Emblems
CDC Decklid Panel
CDC Sequentials
Raptor Shift Light
MSD DashHawk
|
|
|
|
|
Printable Version
