Coast Driveline 1-piece aluminum driveshaft install (w/pics)
Login  | |
|
Coast Driveline 1-piece aluminum driveshaft install (w/... - 7/31/2007 2:04:03 PM
|
|
|
TacoBill
Posts: 381
Joined: 6/21/2006
Status: offline
|
This ‘How-To’ will cover the installation of the Coast 1-piece aluminum driveshaft.
Tools required
Various metric sockets (10, 12 (12 point), 13, 18mm)
12mm (12 point) ratcheting box end wrench (optional)
12mm (12 point) crows foot extension
Universal joint socket
Socket extensions (various lengths)
Blue Loctite
Torque wrench (up to 76 lb-ft)
Long flat blade screwdriver (or equiv. pry tool)
Brake cleaner (or equiv.)
Straight edge razor blade
Masking tape
Markers (2 different colors)
Estimated install time: 2 to 4 hours
Note: Special instructions added if installing a BMR front safety loop.
Note: Special notes included if you have a MGW shifter and are planning to install a BMR loop.
Installation
1. Jack the vehicle up as high and safe as possible. Always use jack stands!
2. Using a suitable marker (I used paper ‘white-out’), index mark the 6 o’clock position of the forward transmission output flange and the rear pinion flange.
Using a different color, mark the orientation of the driveshaft to the 2 flanges (in the event the OEM driveshaft is ever reinstalled).
Note: On the rear pinion flange, two 6 o’clock index marks were made, one near the pinion seal and one on the driveshaft’s Constant Velocity (CV) joint.
3. With the transmission in neutral, e-brake off, rotate the driveshaft (or have a helper turn the rear tire) for best access to the CV bolts. Set e-brake (so the bolts can be removed).
4. Using a 10mm socket, remove the (6) CV joint bolts.
Note: After the removal CV joint washers (the long crescent shaped washer that joints 2 bolts), re-install 3 of the bolts in snug, staggered.
5. Using a 12mm (12 point) socket (or ratcheting wrench), remove the 4 driveshaft flange bolts to the transmission output flange.
Note: Release the e-brake and rotate the driveshaft as necessary to gain access to the bolts. Do not forget to set the e-brake.
Note: Don’t worry, the driveshaft will stay put even after all 4 bolts are removed.
Note: Save these 4 bolts, they will be re-used.
6. Using a suitable pry tool (a flat blade screwdriver worked fine for me), insert it into the U-joint at the position shown. The driveshaft will compress slightly to allow the driveshaft flange to disconnect from the transmission flange.
Leave it in this disconnected state.
Note: Move back to the pinion flange and remove the 3 bolts from step 4 Note.
7. Place a couple pieces a 2x4’s on top of the mid-pipes to keep the driveshaft from falling onto the pipes once the center bearing bracket is loosened.
8. Using a 13mm socket (and universal joint adapter if required), remove the 2 bolts from the center bearing bracket (located about mid-way on the driveshaft).
9. Driveshaft is now completely unbolted from the vehicle and now can be positioned to be removed through the rear in-between the mid-pipes.
Note: After the driveshaft is removed, make sure both spacer washers that were under the center bearing bracket are removed off the body.
Driveshaft comparison
Pinion Angle
With the driveshaft removed, and if your car is lowered, use an angle gauge to determine what your pinion angle is.
With the car positioned at the same angle as it is on the ground (1/2” forward rake for me with the Steeda Ultralite springs), I jacked the rear pumpkin to the desired height in relation to the front, loading the rear suspension.
Front transmission output flange measured at -3.0 degrees.
Rear pinion flange measured -1 degrees.
If I’m correct, my pinion angle is -2 degrees in relation to the front.
I’ve been told that Ford’s spec on the pinion angle is between -2.75 and -3.0 degrees.
10. Preparation for new driveshaft installation
A thorough cleaning must be done on the rear pinion flange prior to the installation of the adapter plate. According to Coast, the adapter is machined to a zero tolerance fit, so to have it mate against the pinion flange without any debris (Loctite, grease, etc.) in-between is absolutely critical!
Clean off any thread locker off the threads from the factory CV joint bolts as well as the driveshaft flange bolts.
Using a plastic scraper and/or single edge razor, carefully scrape off any dried thread locker off from the pinion flange.
Pinion flange should look as clean as this.
10A. Position the Coast adapter plate into the pinion flange and using the six bolts, evenly draw the adapter into the flange using a standard ‘star’ torque pattern until all 6 bolts are tight (but, not torqued).
Note: Do not put any Loctite on these bolts yet, must be installed dry at this time to avoid any Loctite from dripping in-between the adapter and pinion flange (Yes, it’s that critical!).
Note: The pinion flange depth is approx. 0.400” and the adapter step (that get’s inserted) is approx. 0.550”. So when drawn down and mated, about a 0.150” gap on the adapter will be visible.
Note: To ensure the adapter is fully and evenly seated onto the pinion flange, rig up a magnetic dial indicator (or hold stationary anything non-metallic) and have a helper turn the tires to check for flatness/trueness on the face of the adapter.
10B. Once the adapter plate is fully seated, remove one bolt at a time and apply Loctite on the threads, re-install, and torque to 41 lb-ft.
Note: I used a piece of masking tape to mark each bolt that I Locktited and torqued to avoid any confusion.
All 6 CV joint bolts installed.
Special Section: BMR front safety loop
Whether you need a safety loop is all up to you.
Here’s NHRA’s take on it..
A driveshaft loop will be required on all cars running 13.99 or quicker and utilizing slicks, except vehicles equipped with street tires running 11.49 or slower.
For those installing a BMR front safety loop, see the installation steps below.
For those not installing a safety loop, skip to step 11.
BMR1. Remove the 2 rear transmission crossmember bolts using an 18mm socket
BMR2. Mount the BMR driveshaft loop mounting crossmember to the transmission crossmember, re-install the factory bolts and torque to 55 lb-ft.
BMR3. Insert the new drive shaft though the BMR loop and let it hang until the 4 bolts on the driveshaft flange to the transmission output flange are installed and torqued complete.
(no picture)
BMR4. Mount the loop portion to the crossmember portion using the supplied bolts and nuts.
BMR5. Position the loop so it’s even on both sides of the driveshaft (can use you fingers to check for even gap).
(no picture)
BMR6. Tighten the 2 bolts and ensure the even gap is maintained.
Special Section: MGW Short Throw Shifter
If you have a MGW shifter, the BMR loop will interfere with the adjustable shifter block on the 1-3-5 shifts.
To eliminate this riding condition, you’ll need to fabricate a shim that will be placed between the BMR crossmember and the safety loop.
A 0.250” (1/4”) shim was fabricated, but the shifter block just barely makes contact with the loop on the 1 shift (3 & 5 do not make contact).
Note: The supplied BMR bolts will be too short with the addition of a shim. Longer bolts will be needed to accommodate the shim and to allow at least 2-3 threads to protrude past the plane of the nut.
I recommend obtaining either 1 ½” or 1 ¾” long Grade 8 bolts (BMR supplied bolts are 1” long).
Note: I have the shifter block turned all the way in (then backed out to align the black arrow to the drivers side) at zero turns to give as much clearance to the loop as possible. Throw is a tad longer than what I had at 6 turns, but still feels very good and is still shorter than the stock throw.
Neutral
1st Gear
Note: With the rear suspension unloaded and with the 0.250” shim in place, there is a 0.390” gap between the bottom of the driveshaft and the loop. So this means that I can afford to go with a thicker shim (I’m thinking 0.350” think) to eliminate the 1st gear interference and still have a gap between the loop and driveshaft.
I have not tried this yet, but when I do, I will update this thread.
11. New driveshaft installation
With the e-brake off, index the 6 o’clock marks you made on the pinion flange and transmission output flange.
Position the new driveshaft up from the rear in-between the mid-pipes and carefully route up to the front.
Place rags over any sharp objects to avoid scratching the new aluminum driveshaft.
Note: If you accidentally ding any part of the driveshaft, STOP your installation and contact Coast at 800-533-8087 for advisement.
Let me put it this way, my first driveshaft arrived with a small, smooth dent (thanks to UPS) and Coast flat out rejected it for use.
Mate up both ends of the driveshaft’s U-joints against the rear pinion adapter plate and the forward transmission output flange.
Rotate the driveshaft if necessary to pick up the previously used 4 bolt holes in the transmission output flange, and make sure the 6 o’clock markings didn’t move while rotating the driveshaft.
Once everything is in position, Loctite each bolt and snug down tight. Using an ‘X’ pattern, torque the bolts to the following;
Driveshaft to transmission output flange: 76 lb-ft
Driveshaft to pinion adapter plate: 41 lb-ft
Note: A standard socket – universal joint adapter – ratchet combo will not fit squarely on the U-joint bolts. Correctly torquing these bolts will be difficult without a 12 point Crow’s Foot.
If you choose to use a Crow Foot extension, use the following formula to set your correct torque value.
(T x L) / (L + E) = Adjusted torque value (what you set on your torque wrench)
T= target torque value
L= length of torque wrench in inches (end of handle to center of socket)
E= length of extension in inches (center of socket to center of bolt)
If using a 1” Crow’s Foot extension on the front U-joint bolts, here’s the way the formula works out.
(76 x 12” torque wrench) / (12” torque wrench + 1” extension) = 70.15 lb-in torque.
Installation complete! 
Note: According to Coast’s written instructions as well as a few online sources, there seems to be a clearance issue between the e-brake cable bracket and the driveshaft. Instructions will have you re-drill the bracket bolt hole and move it 1.5” away from the driveshaft tunnel.
On my 2006, I don’t see any bolt attaching the bracket to the tunnel. Instead, it looks to be spot welded on or something, nor do I see no clearance issues between these two. With the rear suspension unloaded, there’s a good amount of clearance between the bracket and cable to the driveshaft so I don’t see a need to relocate this bracket.
_____________________________
Current Status: Blown Motor
MMR Street Mod 800 Shortblock Ordered.. yeah, it'll have FORGED internals
|
|
|
|
|
|
|
RE: Coast Driveline 1-piece aluminum driveshaft install... - 7/31/2007 2:18:25 PM
|
|
|
MELLOWYELLOW06
Posts: 2138
Joined: 10/13/2006
From: WEST LOS ANGELES
Status: offline
|
Will you help me install one in mine, Sir Tacobill?
Humbly yours,
Mellowyellow06
_____________________________
Watch the car in some Drift Action!!
http://www.youtube.com/watch?v=PfeJnPH3moA&feature=related
|
|
|
|
|
RE: Coast Driveline 1-piece aluminum driveshaft install... - 7/31/2007 3:20:31 PM
|
|
|
BigDave
Posts: 632
Joined: 4/23/2006
From: Charlotte NC
Status: offline
|
Great write-up, as usual. Your photography is always outstanding. What camera do you use?
I think the best thing about it is the fact that your son is involved in your car hobby. My 22 year-old couldn't change a valve stem cap and my 18 year-old is interested, but lives in Oklahoma and I rarely see him. I have 4 more boys 9, 3, and the 10-month twins to hopefully addict to cars (especially Mustangs!). We'll see...
_____________________________
2005 GT, KB supercharger (8lbs/intercooled) 433RWHP/399tq
SSE Gen2 fascia, GEF Legend hood/ducktail
GT-500 style wheels (yeah, Chinese)
275/40/17 G-Force Sports
12.55@113, 2.00 60' (on highway tires)
www.BlackSharkRacing.com
|
|
|
|
|
RE: Coast Driveline 1-piece aluminum driveshaft install... - 7/31/2007 3:28:45 PM
|
|
|
EskimoPie
Posts: 102
Joined: 3/30/2007
Status: offline
|
Awesome post as always TB... now what are your driving impressions with the new DS?
_____________________________
On Order:
2008 GT Premium Vert - Vista Blue / Dark Charcoal
|
|
|
|
|
|
|
RE: Coast Driveline 1-piece aluminum driveshaft install... - 7/31/2007 3:59:10 PM
|
|
|
06GT4RAD
Posts: 2147
Joined: 3/25/2006
From: Nor Cal
Status: offline
|
Great Write up as usual Bill.
Moose I am certain Bill is using Jack Stands since he makes it a point in his directions. As for the car being clean. Mine may be as clean as Bill's underneath but my guess is he wiped things down while he was under there so he may have me beat. I know i do not drive the car during the rainy season and currently the car has not been driven in about 3 weeks due to all sort of road construction around my house. The main Hwy is being repaved and until it gets done and all the loose asphalt has gone away the car will stay in the garage.
Richard
< Message edited by 06GT4RAD -- 7/31/2007 4:01:16 PM >
_____________________________
2006 GT-Borla Stingers, Eibach Pro Kit, Tokico D-Specs, MGW Billet, 20" Foose Nitrous w/BFG KDW Tires, CHE panhard bar & Support
http://www.ca-mustangs.com/home.php
|
|
|
|
|
RE: Coast Driveline 1-piece aluminum driveshaft install... - 7/31/2007 4:29:52 PM
|
|
|
MIKE562
Posts: 343
Joined: 11/22/2006
Status: offline
|
Whenever I have a question regarding our Mustangs, I ask myself this: WWTBD? (What would Taco Bill Do?)  You rock  Excellent write up
_____________________________
2006 Black Mustang GT
K&N intake w/ 91 perf. tune, Borla Stingers, o/r h-pipe
|
|
|
|
|
RE: Coast Driveline 1-piece aluminum driveshaft install... - 7/31/2007 4:38:23 PM
|
|
|
marcuskeeler
Posts: 2428
Joined: 9/25/2006
Status: offline
|
Great install write up as always Bill. Would like to know if there is more/less driveline vibration ?
Pics were taken with a Canon PowerShot SD550 by the way,
< Message edited by marcuskeeler -- 7/31/2007 4:39:52 PM >
_____________________________
www.mkeeler.com/mustang/
Minority group member - I like going round corners
|
|
|
|
|
RE: Coast Driveline 1-piece aluminum driveshaft install... - 7/31/2007 5:10:08 PM
|
|
|
NickSezz
Posts: 1153
Joined: 5/16/2006
From: Nutley NJ
Status: offline
|
It looks like you can eat off of the under side of your car. I am in awe everytime I see how clean and perfect everything is. Your son is going to have a great thing passed on to him.
This is a great thing you do for everyone on here and I bet you enjoy making these wright ups just as much as we do reading them.
_____________________________
2005 Mustang V6 Manual, BrenSpeed 93 tune SCT, MMR Intake w/MMR TBS, MRT Exhaust, TB Bypass, 17" 2006 GT Takeoffs, MUSTANG 3rd brake light decal, Rear BLACK OUT Panel, Custom Strut Bar, LSD/3.73s, 20% TINTS, GT Sway Bars, AEM Wideband
|
|
|
|
|
RE: Coast Driveline 1-piece aluminum driveshaft install... - 7/31/2007 5:16:41 PM
|
|
|
TacoBill
Posts: 381
Joined: 6/21/2006
Status: offline
|
Thanks everyone for the kudos, I really appreciate it!
quote:
ORIGINAL: MELLOWYELLOW06
Will you help me install one in mine, Sir Tacobill?
Umm.. it was a once in a lifetime experience. Let me reiterate, once.
quote:
ORIGINAL: EskimoPie
Awesome post as always TB... now what are your driving impressions with the new DS?
Nothing yet. My test drive has been limited to backing it out from the garage and re-parking it!
Need to fabricate a thicker shim and get longer bolts (for the BMR loop) before I go on a 'fun' test.
quote:
ORIGINAL: moosestang
I didn't see one spot of rust on anything under your car!
I know you weren't under that car with just that craftsman floor jack supporting it. Please tell me there were some jackstands somewhere out of site.
Not my daily, hasn't seen rain (yet). Makes working under the car pleasurable (to a point  ).
C'mon Moose, you know be better than that. I took these pics, but didn't post them in the original write-up.
quote:
ORIGINAL: marcuskeeler
Would like to know if there is more/less driveline vibration ?
Pics were taken with a Canon PowerShot SD550 by the way,
See my response to EskimoPie's question.
When I do add the shim and bolts, look for my SOTP meter feedback here.
Correct on the SD550. Small enough to snake in some pretty tight spots.
_____________________________
Current Status: Blown Motor
MMR Street Mod 800 Shortblock Ordered.. yeah, it'll have FORGED internals
|
|
|
|
|
RE: Coast Driveline 1-piece aluminum driveshaft install... - 7/31/2007 5:38:21 PM
|
|
|
jdt141
Posts: 137
Joined: 5/22/2007
Status: offline
|
and (for the newbies like myself) what would the benefits of this driveshaft be?
_____________________________
|
|
|
|
|
|
|
RE: Coast Driveline 1-piece aluminum driveshaft install... - 7/31/2007 5:42:37 PM
|
|
|
Stkjock
Posts: 2767
Joined: 1/18/2007
Status: offline
|
quote:
ORIGINAL: jdt141
and (for the newbies like myself) what would the benefits of this driveshaft be?
less rotating mass=less parasitic loss of hp... more acceleration!!
Taco.... love the fading rocker strip as well...
_____________________________
Tngstn 06GT-5 spd -Vortech HO S/C-Tuned by Realspeed Auto
You can never have too much power, just not enough traction.
12.33 @ 112.3 - 1.71 60"
|
|
|
|
|
RE: Coast Driveline 1-piece aluminum driveshaft install... - 7/31/2007 6:18:21 PM
|
|
|
sleeper2
Posts: 557
Joined: 3/13/2007
Status: offline
|
Great Job Tacobill! Thanks for setting aside time to take all the pictures during the install.
Sleeper2
|
|
|
|
|
RE: Coast Driveline 1-piece aluminum driveshaft install... - 7/31/2007 7:09:07 PM
|
|
|
TacoBill
Posts: 381
Joined: 6/21/2006
Status: offline
|
quote:
ORIGINAL: PLstang
Awesome write up, any particular reason you went with the Coast 1 piece? Where are they available at? I just don't believe I've heard of the brand and I have been considering this (1 piee DS) as my next mod and would be interested in hearing your reasons for your choice.
I got the Coast driveshaft and BMR front safety loop package from Tillman Speed. CR (at Tillman Speed) gave me a great price as a package deal.
The 1-piece driveshaft community seems to be split in two. One for the adapter plate (like the one I just installed) and the other for replacing the pinion flange. I'm not going to debate which is better because the point is moot. All I can say is that it boils down to personal preference as both types of driveshafts are extremely reliable and net about the same amount of performance.
I went with Coast for 2 reasons. One, like I mentioned, was offered to me at a great price. Two, I didn't feel like tearing into my pinion flange to swap it out (no matter how easy it's supposed to be). I recently had a set of 4.10's installed and it has absolutely no gear whine, groan or moan. I wanted to leave good enough alone and not mess with anything associated with my perfectly installed gears.
BTW, the runner up driveshaft would've been the Steeda 3.5" aluminum unit, but that would've cost me an additional $200 or so.
quote:
ORIGINAL: Stkjock
less rotating mass=less parasitic loss of hp... more acceleration!!
Taco.... love the fading rocker strip as well...
I agree... with both statements!
_____________________________
Current Status: Blown Motor
MMR Street Mod 800 Shortblock Ordered.. yeah, it'll have FORGED internals
|
|
|
|
|
RE: Coast Driveline 1-piece aluminum driveshaft install... - 7/31/2007 7:57:54 PM
|
|
|
blaven
Posts: 617
Joined: 4/22/2006
Status: offline
|
Great write up, one of those is in my future but for right now i'm done with mods until i can get some more funds saved up
_____________________________
SOLD:(MRT Struts,Stingers,O/R H,Hurst,Roush Louvers,Eibach,CDC Ducktail/Classic Chin,Bspeed C&L 93,Raptor,Clear corners,Center Grill,Rotorpros, 20x9 Razors,Nitto 555 275/255/35's
|
|
|
|
|
|
|
RE: Coast Driveline 1-piece aluminum driveshaft install... - 8/4/2007 8:37:57 AM
|
|
|
TacoBill
Posts: 381
Joined: 6/21/2006
Status: offline
|
*NEW UPDATES*
New 0.350" shim is in place along with longer Grade 8 bolts (1 1/2" long) and everything is fine, no riding conditions between the safety loop and MGW shifter block.
Also, I was able to safely turn the MGW shifter block out to 5 turns.
I think I know which e-brake bracket Coast is talking about that needs to be moved 1 1/2" away . It's a small support clip/bracket that supports the e-brake cable that goes to the passenger side brake. On an aggressively lowered car, I can possibly see some clearance issues to the bolt head of that clip/bracket if not re-located.
See pic below for reference.
Took the car out for a short test drive mainly to check for anything wierd (vibrations, etc.). Couldn't open her up on the highway because of traffic, but I went to my secret proving grounds and got up to 80 and no vibrations!
I didn't do any hard 'off the line' launches, but I can tell that it feels lighter under there. Also noticed that the car doesn't engine brake as slowly as it used to (it coasts faster in gear now).
Until I get on it, I can't say with certainty whether or not this was a good cost vs SOTP mod. At worst, it'll look good on my show poster.
Here's some final install pics.
_____________________________
Current Status: Blown Motor
MMR Street Mod 800 Shortblock Ordered.. yeah, it'll have FORGED internals
|
|
|
|
|
Printable Version
Especially if the price is right!
