Okay, before you start bashing me, let me just say that this is written for the ‘1st Timers’ who haven’t attempted an oil change, but were thinking about doing it themselves if they only had some simple steps to follow.
Here we go…
I went with the fully synthetic Mobil 1 5W-20 and the Mobil 1 (M1-210) High Efficiency oil filter. A total of 6 US Quarts was used.
First thing was to warm up the engine a bit so the oil can flow easier, but not too hot. I drove it up on the Rhino Ramps and let it idle for a few minutes.
Standing in front of the engine, looking down, you can see the factory oil filter right of center (the all white one).
From underneath the car, locate the oil pan (black one), just forward of the transmission bell housing.
Use a 16mm socket to break loose the drain plug and carefully unscrew the nut by hand. Caution! The oil may be a little warm so be careful. Don’t forget to position your drain pan under the plug, and please, make sure it’s big enough to hold 6 quarts.
While the oil is draining out (I let it go for few minutes), remove the oil filler cap and clean up the plug.
Now, re-install the drain plug (careful not to cross-thread it) and tighten it using the socket and ratchet. Torque is 26Nm, 19lb-ft. I just tightened it to what I felt was tight, but not crazy tight.
Now here came the fun part… Not!
Let me first say that the Factory put this filter on very tight! So tight, that there was no way in removing it without causing some damage to its housing.
Here’s a shot of the filter from underneath the car.
I tried everything to get that sucker loose. My Hulk rubber gloves failed, rubber strap wrench failed, an even a filter socket failed! I had no choice, but to employ the Jaws of Life! This did the job, but not without putting some major dents in the filter. But, who cares as it was getting tossed.
Once the filter is loose, carefully (and slowly) spin it off and let the excess oil drain into your pan. Oil will drip over other parts, can’t help that. Once the filter is removed, make sure the rubber seal off the OEM filter isn’t still stuck to the engine block. Get a clean rag and wipe the mating surface and any spills.I read one idea about covering the downward hose with some aluminum foil for easy clean-up.
Open up one of your new quarts of oil and rub a light coat over the rubber seal/gasket on the new filter. I also rub some oil into the threaded hole to for good measure, although probably not necessary.
Addendum: Another option; the oil pressure will come up faster by not having to fill the filter from the oil pan. You can easily fill it (the new oil filter) about 3/4 the way up without having it spill out when installing it.
Install your new oil filter and be careful not to cross-thread it while screwing it on. Once the filter gasket made contact with the block, I gave it an additional ¾ to a full turn BY HAND. Do not over-tighten the filter.
A couple pictures from above, looking down.
Checklist before filling the engine with new oil… drain plug tight? New oil filter on and tight? Good! Now, start filling. Don’t pour in the quarts like a maniac, it may spill over your funnel (bad thing).
(Here’s my proof that I actually did it.)
Once you’re done filling, replace your oil filler cap and go do a quick courtesy check for any leaks. Good? Go for the engine start. Now don’t go revving the engine as soon as it starts, there’s plenty of time for that later. Also, keep an eye on the oil pressure gauge (if equipped) and make sure it shows pressure within a couple seconds of starting the engine.
What I usually do now, is get back under the car and re-check for leaks.
Once all looks good, go ahead and back the car off the ramps (or whatever means you lifted it) and shut the engine off. Let it sit for at least 5 minutes and check the oil dipstick level. It should read at the upper end of the top hole.
Being the oil is fresh and new, seeing it on the dipstick can be a little difficult.
Job is complete!
Just for fun, here’s a pic of what I used.
_____________________________
Current Status: Blown Motor MMR Street Mod 800 Shortblock Ordered.. yeah, it'll have FORGED internals
Good writeup if there is one thing the Mustang community is missing its DIY for simple things. There are a lot of true gear heads who could do an oil change before they could drive who pass over helping newbies with the basic stuff.
Nice post, I'm sure that helped for those owners that weren't sure how to do it. I wouldn't use a Mobile Filter, you see they make oil, not filters, and that's probably a Fram, or whatever with a "private label", marked up in price cuz it sez Mobile. If I may add, use a blanket or some type of "fender protector", in the one photo, you are very close to scratching the fender with your belt buckle.
< Message edited by LegallyTorchRED -- 4/17/2007 12:48:27 PM >
Posts: 61
Joined: 1/15/2007 From: League City, TX Status: offline
Bill, thanks for your time and dedication to the forum. I could have used a newbie's guide to installing a Vortech supercharger about three days ago! :-)
I would agree not to use a Mobile one oil filter or any other "oil branded" filter. I was in the Auto Parts industry for 6 years as well as ASE certified, and the best oil filters on the market for Ford products are either a WIX, Hastings, or a Motorcraft Racing oil filter. Any of these have steel on each end of the filter element on the inside of the canister to help prevent collapsing under pressure, as well as a steel shaft connecting each end, and a teflon grommet as well on the inside. Most of the "oil branded" oil filters as well as Fram, and STP have cardboard on the filter element ends that will break down quicker and possibly collapse under heavy pressure. However they have really good marketing to support their products and make them look better. I basically use only Wix because they are the easiest to find out of the three.
Other than that, great article. I believe it will help alot of people that may be new to all this.
Always, always, ALWAYS make sure the old gasket is off the engine. You'll have a big mess to clean up. 6 Quarts of oil drains a lot faster that way then with the oil plug.
I wouldn't use a Mobil Filter, you see they make oil, not filters, and that's probably a Fram, or whatever with a "private label", marked up in price cuz it sez Mobil.
quote:
ORIGINAL: 07moneypit
I would agree not to use a Mobil one oil filter or any other "oil branded" filter. I was in the Auto Parts industry for 6 years as well as ASE certified, and the best oil filters on the market for Ford products are either a WIX, Hastings, or a Motorcraft Racing oil filter. Any of these have steel on each end of the filter element on the inside of the canister to help prevent collapsing under pressure, as well as a steel shaft connecting each end, and a teflon grommet as well on the inside. Most of the "oil branded" oil filters as well as Fram, and STP have cardboard on the filter element ends that will break down quicker and possibly collapse under heavy pressure. However they have really good marketing to support their products and make them look better. I basically use only Wix because they are the easiest to find out of the three.
Okay guys, I understand both your points and they are valid, ... to an extent.
I also have done my fair amount of research when I was selecting which oil filter to go with. I don't want to turn this thread into a debate on oil filters (please start a new thread if you want to debate brand A vs brand B), but I will point out some info which may help others decide what brand filter to go with.
Here are the core components that make up the M1-210 oil filter:
Filter Weight - 16.8 oz
Overall OD - 3.67"
Overall Height - 3.71"
Can Material - 0.02" thick steel
Filter Element OD - 3.36"
Filter Element Height - 2.57"
Media - Synthetic (appears pink/orange)
Number of pleats - 55 + 1 joint
Depth of pleats - 0.72"
Media length (unrolled) - 89.3"
Media width (glue not included) - 2.1"
Media thickness - 0.030"
Total media surface area - 187 sq. in.
Total media volume - 5.6 cu. in.
Inner Filter Support Material - 0.015" Thick Perforated Steel
Inner Filter Support OD - 1.66"
Indentifying marks Can - 06190602 / Product of USA ADBV - AAX / 40 Base - ZZ
Gasket Retention - Press Fit
Thread - M22 -1.5
Relief Valve Location - dome end
ADBV Material - Silicone (orange)
Gasket includes lubricant
The line of Mobil 1 oil filters are made by Champion Laboratories'.
And, just for the record, Purolator makes Ford Racing and Ford Motorcraft, Fram makes their own, Affinia Group Inc makes Wix, and Clarcor Corp. makes Hastings.
So, is the Mobil 1 oil filter the best filter out there for our Mustangs? Of course not! Is it a 'better than average' filter that does an adequate job at filtering particles down to 10 microns? Absolutely!
btw- With all that said, I have a Ford Racing oil filter ready to go for my next oil change.
_____________________________
Current Status: Blown Motor MMR Street Mod 800 Shortblock Ordered.. yeah, it'll have FORGED internals
Thanks for that post Taco! Nice photo job and nice writing technique. Simple and well described enough to prompt even me to want to start changing my own oil. I'm not a gear head, but I've done a thing or three with my own cars over the years. My excuse is usually, "I'm too busy earning the bucks that can pay for the conveniences in life... so why not have it done for me." But I've been learning lately that with that approach, one can really miss out on some great satisfactions in life.... one of the greatest ones being the "do it yourself" one.
All I need are some Rhino Ramps, oil filter wrench and a good drain pan. I use Mobil 1 oil already and I'm sure I pay too much for oil changes. Buying that gear and 2 or 3 oil changes on my own and I'd be saving some notable cash as well as enjoying myself in the process.
One question Taco, any advice on old oil disposal? I live in a suburban neighborhood with trash pickup and they even do recyclables, etc. I suppose I could call them, but I thought I'd ask for your tip on that one too.
One question Taco, any advice on old oil disposal? I live in a suburban neighborhood with trash pickup and they even do recyclables, etc. I suppose I could call them, but I thought I'd ask for your tip on that one too.
+1 .. I saw that you live in Torrance. I live in LA.. Any good places that you know of to drop off the old oil?
and as always, fantastic write up.. you rock bro.
< Message edited by teksp0rt -- 4/17/2007 11:58:47 PM >
_____________________________
06' Mustang GT = Sold. Hopefully I will be one of the first with the new '10!
Just go to the nearest gas station and ask them. You know those circular bumps in gas station parking lots? One of those is for oil disposal. Just make sure to ask them while mechanics are in the garage. If you ask Derka Derka at midnight he is going to be clueless.
Posts: 337
Joined: 1/31/2007 From: Virginia Status: offline
quote:
ORIGINAL: celenztah
One question Taco, any advice on old oil disposal? I live in a suburban neighborhood with trash pickup and they even do recyclables, etc. I suppose I could call them, but I thought I'd ask for your tip on that one too.
In my area, used oil can be dropped off at most large auto parts stores. Advance and Pep Boys is where I usually drop mine off. I like to drop off my old oil when I buy the new oil so that they can realize the continued benefit of allowing customers to recycle at their store. Just call around to your local parts stores and see who will take it.
One question Taco, any advice on old oil disposal? I live in a suburban neighborhood with trash pickup and they even do recyclables, etc. I suppose I could call them, but I thought I'd ask for your tip on that one too.
The recycling in my area is exactly why I take the car in to have the oil changed. My town has said it's a big no-no to do your own oil changes, because it is considered "hazardous waste". So, I can't do an oil change in my driveway anymore, and I certainly cannot do it on the street. Also, the "recycling center" here in town charges to recycle oil! I've tried to take it to the local CSK, AutoZone, and PepBoys stores for recycling, but they all say that I can only bring in 2 gallons at a time. So, I basically either get charged twice, or I have to find a way to transfer the oil in to 2 1 gallon milk jugs, thus causing more of a chance of spill and "hazardous waste", or I can pay someone to change the oil for me, for about the same price that it would cost me to buy the oil and do it myself...Guess which option I choose?
Sorry, Bill, not bashing on your oil changing procedure...I think it's great, and if it weren't for local city politics being what they are, I'd be following your pictures and directions step by step. Definitely a help for the average newbie who doesn't know how to do a simple oil change. :) The only thing I'd include in your steps is that if you use a set of toothed pliers (i.e. channel locks or that clamp wrench like you used) that there is possibility of puncturing the metal on the filter itself and causing another leak and mess to clean up...But sometimes, that's what it takes to get that sucker off!
_____________________________
2007 Tungsten Grey Mustang GT Bone stock
1974 Chevrolet Corvette (in the process of rebuilding)
1967 Jaguar E-Type 2+2 4.2L, British Racing Green, aka The Green Penis
Posts: 202
Joined: 10/1/2006 From: Riverside, CA Status: offline
Yet another nice write up from TacoBill. I have already changed my oil once, at 1000 miles, and my filter came off with no problems. I am going to miss changing oil in my Ranger. (The Mustang is replacing the Ranger) I did a 4 inch suspension lift on it so when I changed oil I did not need to jack it up. The oil filter is perpendicular to the ground so I could fill it up with oil. fd
One question Taco, any advice on old oil disposal? I live in a suburban neighborhood with trash pickup and they even do recyclables, etc. I suppose I could call them, but I thought I'd ask for your tip on that one too.
Vince, as suggested by others, most all autoparts stores will take your used oil. For me, my local Autozone takes the oil at no charge. I have a 5 gallon drum that I use to store the used oil and once full, I take it in.
Also, I see that you have a 4.0. There are a few differences that you need to take note of.. The 4.0 takes 5 quarts of 5W-30 (the GT's take 6 quarts of 5W-20). The oil filter is located on the Passenger side. Socket size of the oil drain plug is 13mm.
quote:
ORIGINAL: teksp0rt
+1 .. I saw that you live in Torrance. I live in LA.. Any good places that you know of to drop off the old oil?
Dennis, pretty much what I said above, I take it to Autozone (I'm sure other will accept it as well as some gas/service stations).
quote:
ORIGINAL: schmitty
great post, but are you sure you even needed a oil change?? it doesnt even look like that car has been driven. sooo clean under the hood.
Hey Jason, I have a whopping 1100 miles now! As you probably have guessed, it's not my daily. I spoke to a Mobil 1 tech about an oil change schedule for me and was told to do it once a year. That being said, my next oil change will be coming up this December.
_____________________________
Current Status: Blown Motor MMR Street Mod 800 Shortblock Ordered.. yeah, it'll have FORGED internals
One question Taco, any advice on old oil disposal? I live in a suburban neighborhood with trash pickup and they even do recyclables, etc. I suppose I could call them, but I thought I'd ask for your tip on that one too.
Vince, as suggested by others, most all autoparts stores will take your used oil. For me, my local Autozone takes the oil at no charge. I have a 5 gallon drum that I use to store the used oil and once full, I take it in.
Also, I see that you have a 4.0. There are a few differences that you need to take note of.. The 4.0 takes 5 quarts of 5W-30 (the GT's take 6 quarts of 5W-20). The oil filter is located on the Passenger side. Socket size of the oil drain plug is 13mm.
Thanks Taco for the update on those 4.0 differences (the 5W-30 I was aware of - I bug my current mechanic each time to make sure that's what he puts in... lol).
And thanks all for the oil recycle suggestions. I live very close to Advance Auto Parts, Mechanic shops and gas stations. Transporting the oil would mean one more thing-a-muh-bob to buy (and a wide funnel!), but still should be worth it.
i have always wanted to know how to change oil and this actually worked well. i think if i took my laptop out and did everything step by step the way you said i can do it. but its nice taking my car in to the dealer and having them inspect everything else still.
Printable Version
Oil Change: For those who want to do it themselves, but... - 
You'll have a big mess to clean up. 6 Quarts of oil drains a lot faster that way then with the oil plug. 
