Moleskin (for window tint) install w/pics and vids
Login  | |
|
Moleskin (for window tint) install w/pics and vids - 4/16/2007 12:22:09 PM
|
|
|
TacoBill
Posts: 381
Joined: 6/21/2006
Status: offline
|
Window tint: Moleskin installation
Here’s the deal, I’ve noticed that the Velcro felt has started to separate from its adhesive backing on a small section on the drivers side wiper channel causing the exposed adhesive glue to streak onto the tint when rolled up and down.
My choice was to either replace the Velcro with another strip, or install Moleskin felt in its place. As I have yet to read any negative comments on the use of Moleskin, I opted for the latter.
I obtained a Moleskin kit from Automoleskin.com. Kit comes complete with enough Moleskin to do both sides and a set of install direction.
Here’s what I did to replace the Velcro with the Moleskin.
Side by side comparison (Moleskin on left)
Roll the window down and remove the (3) 7mm screws as shown in the pics below (2 on the back side of the door panel and 1 on the top forward side). I did not find it necessary to remove any more screws or trim pieces to access the wiper channel.
Access and remove the wiper channel. Grasp the top edge of the door panel towards the rear and with your fingers, firmly lift it up and over the channel. This step takes a little bit of forcing, so don’t be afraid to really pull up on the door panel. Once the channel is accessible, lift up the channel from its end about half way, then slide the rest out.
Here you can see where the Velcro has drooped down, exposing the adhesive glue.
Here is a pic of the orientation of the wiper channel in relation to the track, which it will slide into later.
Velcro felt removal. I was afraid that I was going to have a big mess on my hands after I peeled off the Velcro strip. So, in anticipation of it, I used a blow dryer on the Velcro for a few minutes heating it as much as I can prior to lifting it off.
As you can see, it peeled most all the adhesive off with the Velcro.
I used some 3M adhesive remover and a clean rag to remove any traces of leftover glue residue off the channel.
Next, the contact surface on the wiper channel needed to be prepped correctly in order for the Moleskin to positively bond to it. I used 60 grit sandpaper to rough up the entire contact surface area, end to end.
After scuffing the surface, I used some Isopropyl Alcohol and another clean rag to wipe the entire length of the channel, being careful not to touch the wiped surface with my fingers.
Moleskin layout. The kit enclosed from AutoMoleskin is one long piece, enough to both sides. I laid out the Moleskin strip next to the channel (plus a inch, just incase) and cut it.
As you can see, the width of the Moleskin is wider than the width of the contact area on the wiper. To minimize any chance for the Moleskin to lift, or for any dirt/debris to work it’s way between the felt and channel, I decided to trim the width so it lays perfectly flat on the contact surface (of the wiper). I measured and marked the width at 0.6”, and used a razor and a straight edge to trim along the entire length.
Peel back the backing and carefully start at one end making sure that it lays flush along the top edge of the wiper channel.
Once you get to the opposite end (45 degree side), simply trim it to the edge using a razor.
Moleskin felt installed.
Wiper channel re-installation. Make sure you have the channel properly orientated with the 45 degree cut towards the front (door hinge). Position the end of the channel’s groove into the metal frame (for me, the one painted Torch Red) and slide the channel all the way in. This operation will take a little bit of force to accomplish. Position your hands anyway you wish to give you the best leverage.
Once you can’t push the channel any further into the frame, use a blunt object to push it in the rest of the way.
This shows the final position of the channel installed.
Door panel re-installation. Grasp the top edge of the door panel and pull it over the newly installed wiper channel.
Finishing up. Re-install the 3 door panel screws to complete the installation.
Automoleskin.com recommends not to roll the windows down for at least 12 hours.
Installation complete! 
_____________________________
Current Status: Blown Motor
MMR Street Mod 800 Shortblock Ordered.. yeah, it'll have FORGED internals
|
|
|
|
|
|
|
|
|
RE: Moleskin (for window tint) install w/pics and vids - 4/16/2007 1:28:11 PM
|
|
|
mAnYsTyLeS
Posts: 1316
Joined: 8/3/2006
From: NYC
Status: offline
|
Sweet garage and nice write-up!!!
_____________________________
07 GT - A/T
Steeda Intke - H/F Elbow, SCT 2 - 93 Oct
FR 3.73s, Steeda UDP, Steeda CMCV deletes
MAC Catback, ARH L/Ts & O/R H
Spohn Adj. LCAs, PH Rod, Rr. Sway & BMR PHR Brace
|
|
|
|
|
RE: Moleskin (for window tint) install w/pics and vids - 4/16/2007 3:46:44 PM
|
|
|
TPony
Posts: 9381
Joined: 7/29/2006
Status: offline
|
Dude..you da'man....I installed the felt and so far so good, but if not moleskin is next and your writre up is in my favorites now....thanks.
_____________________________
06 GT, tint, appearance mods, 18X9 w/NT555 255/45/18, GTA Axlebacks, GT500 spoiler/pedals. Many interior billet upgrades.
|
|
|
|
|
|
|
|
|
RE: Moleskin (for window tint) install w/pics and vids - 4/16/2007 4:46:35 PM
|
|
|
Tubra
Posts: 217
Joined: 9/12/2006
Status: offline
|
I love the moleskin. The first time I had my windows tinted, it ended up looking like the grooves of a record. Luckily I found the moleskin cure and the guy at the tint place even redid them for free!!!
_____________________________
Mods: Dual FRPP GTAs, custom H-Pipe
My Cardomain page with more pics!
|
|
|
|
|
RE: Moleskin (for window tint) install w/pics and vids - 4/16/2007 5:19:37 PM
|
|
|
Eleanor06
Posts: 774
Joined: 3/12/2007
Status: offline
|
Yea, thanks.Nice write up!! I've got to do the same thing and this helps alot.
_____________________________
JLT Sct2 93 tune-Bassani x-pipe w/hi-flow cats-Bmr lca's
Magnaflow mufflers-Hurst shifter-GMS sway bar delete
|
|
|
|
|
RE: Moleskin (for window tint) install w/pics and vids - 4/16/2007 5:23:40 PM
|
|
|
WhoMe
Posts: 403
Joined: 2/25/2007
Status: offline
|
This guy is amazing. Somone needs to sticky these things Ive never seen a regular member of any forum put together such nice and well illustrated (PLUS VIDEO!) tutorials. TacoBill..thanks again, and while I dont even have my Mustang yet I know this is definatly a tutorial Ill be referring back to when get my windows tinted.
|
|
|
|
|
RE: Moleskin (for window tint) install w/pics and vids - 4/16/2007 5:23:42 PM
|
|
|
06GT4RAD
Posts: 2147
Joined: 3/25/2006
From: Nor Cal
Status: offline
|
Outstanding as is the norm for Bill.
Thanks for yet another great write up.
Richard
_____________________________
2006 GT-Borla Stingers, Eibach Pro Kit, Tokico D-Specs, MGW Billet, 20" Foose Nitrous w/BFG KDW Tires, CHE panhard bar & Support
http://www.ca-mustangs.com/home.php
|
|
|
|
|
|
|
RE: Moleskin (for window tint) install w/pics and vids - 4/17/2007 6:42:12 AM
|
|
|
CrazyHorse0217
Posts: 395
Joined: 3/28/2006
Status: offline
|
I've had my Moleskins and replacement tint for about 3 months now. No scratches till I noticed a couple on the passenger side yesterday. Very shallow (tint only, not glass). Argggggg!
_____________________________
CrazyHorse
2006 redfire GTcoupe w/ auto trans
3.73 FRPP gears
Roush supercharger w/ pulley upgrade
Roush wheels & Nitto 285/275
Shaker 1000
|
|
|
|
|
RE: Moleskin (for window tint) install w/pics and vids - 4/19/2007 2:33:05 PM
|
|
|
KSBlizzard
Posts: 10
Joined: 3/22/2007
From: Greenville, MI
Status: offline
|
Your tutorial was awesome! Very well written (and video'ed).
Once I get my 'stang I will be following this to install my moleskin.
< Message edited by KSBlizzard -- 4/19/2007 2:46:11 PM >
_____________________________
On order:
'07 GT Premium
Vista Blue / Dark Charcoal
5-speed manual
18" Premium Wheels
3.55 Ltd Slip
Int Upgrade
|
|
|
|
|
RE: Moleskin (for window tint) install w/pics and vids - 4/19/2007 4:00:42 PM
|
|
|
bchataroo
Posts: 180
Joined: 7/4/2006
Status: offline
|
This a great help Taco.
Later
_____________________________
06 Legend Lime GT Auto 18x9 Saleen Wheels
Kooks L/T's w/HiFlo Cats & X-pipe
JLT CAI SCT 3.73's UDP COP's
Eibach Pro-Kit with all the trimmings
|
|
|
|
|
RE: Moleskin (for window tint) install w/pics and vids - 4/19/2007 4:35:47 PM
|
|
|
TacoBill
Posts: 381
Joined: 6/21/2006
Status: offline
|
Thanks for the kind comments everyone. I'm starting to blush.. 
_____________________________
Current Status: Blown Motor
MMR Street Mod 800 Shortblock Ordered.. yeah, it'll have FORGED internals
|
|
|
|
|
RE: Moleskin (for window tint) install w/pics and vids - 4/19/2007 5:56:25 PM
|
|
|
yzfmik
Posts: 250
Joined: 11/23/2006
From: Spring Hill, FL
Status: offline
|
Tacobill rocks!!! Hell he's better than Tacobell!
_____________________________
'05 Red GT Premium - M5, Loudmouth axleback, 5% tint, BSM 10" Stripe Kit
|
|
|
|
|
RE: Moleskin (for window tint) install w/pics and vids - 4/19/2007 6:00:37 PM
|
|
|
Professor Wizard
Posts: 3429
Joined: 3/15/2005
Status: offline
|
WONDERFUL Writeup... THANKS!
_____________________________
-PW (Professor Wizard) 
Vv My Sexy Lady vV
05' Torch Red Vert, Red Int, All Options, Remote Start, Chrome GT's, and other stuff! *Sponsored by Dent Devil*
|
|
|
|
|
Printable Version
