I just put my ripped out my matrix lowering springs, put the stock ones back in on my 97gt, then threw the 20s on. I knew i would sit higher but im really high up its like a 4X4 stang. The rubber im running is 255/35/20. The back end isnt too high up but the front is way to high. Any ideas on how to drop it just a little in the front mabe. I dont really know.
hahahah i mean what kinda springs are good. I got the matrix ones which were kinda cheap and the sucked. i just need a small drop that wont make the wheels rub
Dude you are totally throwing off your final drive ratio! Your car was probably calibrated w/ the 17" 245/45's and now you have increased your overall diameter, which will make your ratio taller than it is supposed to be, hence SLOWER 0-60, in the 1/4, etc.
_____________________________
#58 of 141 75mm s/c Pulley 380 PCM Flowmaster Delta Flow 40's MAC CAI Roush short throw shifter S3 Suspension MAC C / C Plates Jack Roush sig 360.38 rwhp / 367.17 rwtq www.cardomain.com/id/sargepug
dude why teh **** would you put 20's on a mustang? you need a diff car, a mustang just isnt for you
My sentiments exactly!!! I was waiting for someone to say that so I could say how ghetto I think 20's are. That has to look absolutly ghetto on a Stang!!!
Posts: 8826
Joined: 9/2/2003 From: United States Status: offline
Im pretty sure the car's gonna have a 4x4 with wheels that big no matter what you do, unless you get air bags maybe - I suppose its ok if your a ghetto superstar
Posts: 68
Joined: 8/28/2003 From: Shelbyville, IN Status: offline
i dont think he's worried about his 0-60 or 1/4 time ... i doubt he'd go with 20's if he was? i wouldn't think so at least. just go buy a honda and really have the all show no go attitude
_____________________________
03 GT - 5spd - DSG 85mm C&L MAM FRPP 4.10 (soon) bassani o/r x, flowmasters tri ax predator tuned
#58 of 141 75mm s/c Pulley 380 PCM Flowmaster Delta Flow 40's MAC CAI Roush short throw shifter S3 Suspension MAC C / C Plates Jack Roush sig 360.38 rwhp / 367.17 rwtq www.cardomain.com/id/sargepug
Posts: 8826
Joined: 9/2/2003 From: United States Status: offline
quote:
ORIGINAL: c0bra
dude if u want 20'z buy a fukin escalade or sum ****. 20'z on a mustang? im not trying to stereotype you or anyone else in ths forum but u must be mexican, right? not trying to be offensive.
Posts: 250
Joined: 2/1/2004 From: United States Status: offline
Seriously guys, Im not crazy about the ideas of 20s on a mustang either but check out this months issue of MM&FF. There is a mustang in there that has 20s on it and it is sharp. The guy had a set of 20s custom built to look like the bullit rims.
Seriously guys, Im not crazy about the ideas of 20s on a mustang either but check out this months issue of MM&FF. There is a mustang in there that has 20s on it and it is sharp. The guy had a set of 20s custom built to look like the bullit rims.
Yeah that car looks insalely good. It also has no spoiler which looks soooo clean. The thing is though, most "20's" arent Torque Thrust or Bullitt wheels. They are usually nasty bulky Chrome wheels.
Printable Version
Im too high up on 20s - 
RE: Im too high up on 20s - 
YOU BALLING MAN...I GOT 18S
